TIMBER DEALERS.CO.NZList 0

NEW ZEALAND · PROJECT COST GUIDE

Metal Roofing Cost NZ: Roof Sheets, Installation and Re-roofing

Price a metal roof from the total area of its slopes and a list of what the roofer is supplying. The 100 m² Australian installation example below shows a starting budget. For a NZ quote, use the named local sheet price, the profile’s actual installed cover and an itemised installation rate.

Updated 2026-11-17 · Product, tax and installation scope shown separately

Price your own measurementsMetal Roofing Sheet Calculator →

Prices by type and purchase unit

Compare the purchase unit and the scope beside each price. Named retail products are supply only. A contractor benchmark applies to the work and location stated.

NZD price references by type
TypeQuote unitNamed product priceRegional benchmark
Corrugated long-run steellinear metre of sheet / m² installed roofNZ$22.15 / m845 mm nominal width; 0.4 mm steel; special order. Includes GST.Armorsteel 845 × 0.4 mm zinc corrugate roofing steel ↗2026-11-10NZ$150–180 / m²Auckland · GST not confirmedNZ$18,000–26,000 / jobWaikato · GST not confirmedNZ$130–175 / m²Bay of Plenty · Includes GSTNZ$20,000–30,000 / jobCanterbury · GST not confirmed
Tray-profile metal rooflinear metre of sheet / m² installed roofAsk for a supplier quoteNZ$140–200 / m²Bay of Plenty · Includes GST
Concrete roof tilestile / m² installed roofAsk for a supplier quoteAsk for a local quote
Low-slope membrane roofm² of roof plus perimeter detailsAsk for a supplier quoteNZ$200–320 / m²Auckland · GST not confirmed
Polycarbonate roofingsheet / m² of coverNZ$68.16 / sheet2400 × 860 mm sheet. Includes GST.Tufclad Ultra clear polycarbonate 2400 × 860 mm ↗2026-11-10Ask for a local quote

Regional NZ price list

Published rates cover named jobs or products in the areas shown. Match the scope before using a local figure.

Price references and quote coverage by NZ region
RegionPrice in NZDWhat the price coversSource
NorthlandQuote requiredAsk for availability and a measured rate delivered to your postcode.
AucklandNZ$150–180 / m²GST not confirmedCorrugated long-run steelIllustrative simple single-storey gable reroof in Manurewa, 150 m² of roof.South Auckland Roofing Company ↗Checked 2026-11-17
AucklandNZ$200–320 / m²GST not confirmedLow-slope membrane roofPublished 140 m² Māngere Bridge replacement example including substrate and rainwater detail work.South Auckland Roofing Company ↗Checked 2026-11-17
WaikatoNZ$18,000–26,000 / jobGST not confirmedCorrugated long-run steelHamilton/Waikato contractor guide for replacing old iron on a single-storey home with 140–170 m² of roof. Spouting is separate.CTR Roofing ↗Checked 2026-11-17
Bay of PlentyNZ$130–175 / m²Includes GSTCorrugated long-run steelContractor rate for a long-run metal reroof based on quoted work, with strip-out and roof accessories in scope.Bradley Roofing ↗Checked 2026-11-17
Bay of PlentyNZ$140–200 / m²Includes GSTTray-profile metal roofContractor-published installed tray profile replacement range.Bradley Roofing ↗Checked 2026-11-17
WellingtonQuote requiredAsk for availability and a measured rate delivered to your postcode.
CanterburyNZ$20,000–30,000 / jobGST not confirmedCorrugated long-run steelTypical 3-bedroom, single-storey Colorsteel reroof in Christchurch. Confirm roof area and GST.Winter & Son Roofing ↗Checked 2026-11-17
Otago / SouthlandQuote requiredAsk for availability and a measured rate delivered to your postcode.
Other NZ regionsQuote requiredAsk for availability and a measured rate delivered to your postcode.

For any option absent in a region, ask for an itemised local quote. Supply, labour, access and GST can be quoted on different bases.

Types and photo examples

Corrugated long-run steel example
Illustrative image

Corrugated long-run steel

A pitched roof with a compatible metal profile, finish and slope.

Compare effective cover and installed roof area. Identify strip-out, edge protection, underlay, flashings and spouting in the quote.

Tray-profile metal roof example
Illustrative image

Tray-profile metal roof

A clean-lined roof where a tray profile can be specified for the pitch, exposure and substrate.

Confirm tray cover, substrate and junction details. Compare the accessory and clip schedules before applying sheet pricing.

Concrete roof tiles example
Illustrative image

Concrete roof tiles

A pitched tile roof where the structure and access are suitable for the specified system.

Confirm tile weight, compatible battens, ridge, verge and valley parts. A change of roof system may need a separate structural review.

Low-slope membrane roof example
Illustrative image

Low-slope membrane roof

A low-slope area with a designed substrate, drainage route and membrane assembly.

Itemise substrate work, outlets, upstands and penetrations. Agree what testing, warranty paperwork and water protection are included.

Polycarbonate roofing example
Material example

Polycarbonate roofing

A lightweight cover for a patio or similar roof area that needs daylight.

Check profile, effective cover, side laps, sheet length and compatible fasteners or joiners. Verify the support and movement details.

Separate roof covering from a full re-roof scope

Metal roof sheets

Price the exact profile, steel or coating specification, sheet lengths and installed cover. Overall width is not the useful width left after side laps.

For a scheduled metal roof covering.

Polycarbonate and translucent areas

Treat translucent sheets as their own product system with appropriate lengths, supports and laps. Gross sheet area is not an installed-cover price for a mixed-material roof.

For canopies and roof zones using a different covering.

Replacement versus new roof

Existing-cover removal, disposal, substrate inspection and repairs can change a re-roof quote. Ask whether these are included rather than comparing it with new-cover material supply.

For replacing an existing roof rather than ordering sheets for prepared framing.

Flashings, underlay and access

Ridges, valleys, barges, penetrations and roof edges require measured accessories and detailing. Scaffolding or other access, drainage and labour should be stated in the installed scope.

For converting the covering estimate into a complete quote request.

What a new 100 m² metal roof costs in Melbourne

Guardian Roofing’s Melbourne guide uses AUD 80–130 per m² for straightforward new Colorbond installation. A roof with 100 m² measured along its slopes gives AUD 8,000–13,000 at those rates. The guide leaves the GST basis and exact inclusions for the written quote.

Australian examplePublished price in AUDScope to check
New Colorbond on a prepared structure, MelbourneAUD 80–130/m², GST basis unstatedConfirm sheets, fixings, underlay, flashings and ridge capping individually.
Metal roof replacement, SydneyFrom AUD 170/m², GST basis unstatedAussie Roof Repairs publishes a starting rate for supply and installation. Its replacement scope includes stripping the old roof, new sarking and standard flashings.

Metal Roofing Cost — material price checks

Advertised examples checked on 10 November 2026. Each price belongs to the named product and purchase unit. These are source references, not Timber Dealers offers or a completed-job average.

Named materialAdvertised priceTax basisPurchased specification
Armorsteel 845 × 0.4 mm zinc corrugate roofing steelNZ$22.15 / mIncludes GST845 mm nominal width; 0.4 mm steel; special order
Tufclad Ultra clear polycarbonate 2400 × 860 mmNZ$68.16 / sheetIncludes GST2400 × 860 mm sheet

Measure sloped area and useful sheet cover

  • A pitched roof has more surface area than its horizontal projection.
  • Useful sheet cover can be substantially less than overall width.
  • Hips, valleys, penetrations, cut sheets, coating and sheet thickness affect the order.

How to build and compare your budget

Build a measured reroof budget with clear allowances

Separate horizontal footprint from sloping roof area and total lengths of ridges, hips, valleys and eaves. Map penetrations, changes in pitch and blocked access around the building. Ask the roofer whether their rate measures finished slopes and overhangs, and have them check a sheet-length schedule against field dimensions.

For a 150 m² Bay of Plenty replacement with the scope of the published long-run example, NZ$130–175 per m² gives NZ$19,500–26,250 incl. GST. That is the replacement example for the stated system. Record what edge protection, strip-out, underlay and detailing are included before carrying the figure into your own budget.

Request a schedule for scaffold, old material disposal, rain protection and any follow-on items such as fascia, spouting or solar reinstatement. Ask for a variation rate or provisional sum for damaged decking or framing. If the existing material needs specialist identification or removal, make that scope explicit before work starts.

Compare maintenance access and the documentation at finish. Record roof and flashing materials, coating, care measures and who handles future repair calls under the agreed warranties. Keep this with dated photographs of important junctions and the final invoice.

Worked orders you can recalculate

Each example changes one measurement. Open it to see the exact starting inputs, adjust the layout and enter your own quote.

Length along the eave: 6 m

16 sheets × 4.257 m
  • Roof sheets: 16 sheets · 4.257 m per sheet · 68.107 lineal m total
Open this example →

Length along the eave: 12 m

32 sheets × 4.257 m
  • Roof sheets: 32 sheets · 4.257 m per sheet · 136.215 lineal m total
Open this example →

Length along the eave: 18 m

48 sheets × 4.257 m
  • Roof sheets: 48 sheets · 4.257 m per sheet · 204.322 lineal m total
Open this example →

Compare steel thickness, coating and profile

Ask for an itemised scope that identifies the product or system, quantities, tax basis, delivery and the work included.

  • Scaffolding, removal, disposal and installer labour
  • Underlay, flashings, battens, fasteners and rainwater components
  • Structural checks, access and delivery
  • Enter the roof projection including eaves, then calculate slope area.
  • Check profile-specific minimum pitch and side/end laps.
  • Order roof sheets by the actual slope run and confirmed useful cover.

Questions about Metal Roofing Cost

Can I use house floor area as roof area?

Not directly. Include the measured horizontal roof projection and eaves, then account for roof pitch and the actual plane layout.

Is the price per linear metre of roofing a price per square metre?

No. A conversion requires the useful installed cover of that exact profile. Overall sheet width alone is insufficient.

Does the roof-area calculator include roof removal and installation?

It estimates geometry and selected quantities. Re-roof removal, repairs, accessories, access and labour need their own quoted scope.

Read replacement quotations line by line

Sources and technical guidance